Grbl G Code Commands List Pdf < Browser >

1. FUNDAMENTAL G-CODE COMMANDS (Motion) | Command | Description | Example | |---------|-------------|---------| | G0 | Rapid positioning (non-cutting move) | G0 X10 Y20 | | G1 | Linear interpolation (controlled feed cutting) | G1 X5 F100 | | G2 | Circular interpolation (clockwise arc) | G2 X10 Y10 I5 J0 | | G3 | Circular interpolation (counter-clockwise arc) | G3 X0 Y0 I-5 J0 | | G17 | XY plane selection (default for arcs) | G17 | | G18 | XZ plane selection | G18 | | G19 | YZ plane selection | G19 | | G20 | Units: Inches | G20 | | G21 | Units: Millimeters (default) | G21 | | G90 | Absolute positioning (default) | G90 | | G91 | Incremental positioning | G91 | | G93 | Inverse time feed mode | G93 | | G94 | Units per minute feed mode (default) | G94 | 2. SPINDLE & COOLANT CONTROL | Command | Description | Example | |---------|-------------|---------| | M3 | Spindle on (clockwise rotation) | M3 S1000 | | M4 | Spindle on (counter-clockwise) | M4 S500 | | M5 | Spindle stop | M5 | | M7 | Mist coolant on | M7 | | M8 | Flood coolant on | M8 | | M9 | All coolant off | M9 | 3. PROGRAM FLOW & UTILITIES | Command | Description | |---------|-------------| | M0 | Program pause (press resume to continue) | | M1 | Optional pause (if enabled) | | M2 | Program end (same as M30) | | M30 | Program end, rewind to start | | G28 | Go to home position (stored zero) | | G28.1 | Set current position as home reference | | G30 | Go to pre-defined secondary home | | G30.1 | Set current position as secondary home | | G53 | Move in machine coordinates (ignores offsets) | | G92 | Set position offset (temporary coordinate shift) | | G92.1 | Clear G92 offsets | | G92.2 | Suspend G92 offsets | | G92.3 | Resume G92 offsets | 4. TOOL LENGTH OFFSETS (if enabled) | Command | Description | |---------|-------------| | G43.1 | Enable dynamic tool length offset | | G49 | Cancel tool length offset | 5. NON-CONFORMING (GRBL-SPECIFIC) COMMANDS | Command | Description | Example | |---------|-------------|---------| | $H | Run homing cycle | $H | | $X | Kill alarm lock (override safety) | $X | | $N | List startup blocks | $N | | $N0= | Set startup G-code line 1 | $N0=G21 | | $N1= | Set startup G-code line 2 | $N1=G90 | | $RST=$ | Reset all settings to default | $RST=$ | | $RST=# | Clear zero offsets (G92) | $RST=# | | $RST=* | Clear all non-volatile storage | $RST=* | | $C | Check g-code (syntax validation) | $C | | $I | Print build info & version | $I | | $G | Print current active G-code states | $G | 6. STATUS & CONTROL COMMANDS (Real-time) These are single characters, sent without line ending.

| Character | Description | |-----------|-------------| | ? | Report current machine status & position | | ~ | Resume (cycle start) | | ! | Feed hold (pause motion) | | Ctrl-X | Soft reset (clear buffer, alarm state) | View all: $$ View single: $n= (e.g., $130= ) grbl g code commands list pdf